Laboratory tables in contaminated land reports are only useful when the right screening numbers sit beside them. In Australia, the National Environment Protection (Assessment of Site Contamination) Measure 1999, as amended in 2013 (ASC NEPM), puts those numbers in Schedule B1. In short, HILs screen soil for human health, HSLs screen petroleum hydrocarbon vapour risk to building occupants, and EILs and ESLs protect terrestrial ecology. They are not interchangeable. Each set applies to a defined land use, and most also depend on soil type and depth.
This guide covers what each family of criteria is for, plus the petroleum hydrocarbon management limits that sit beside them. It explains the soil types and depths they were derived for, how they relate to soil, groundwater and vapour pathways, and why development sites call for the shallowest (most sensitive) HSLs until finished levels are fixed. Use it for scoping, peer review and client explanation. It does not replace reading Schedule B1, the supporting Schedules, or the state instruments that give the NEPM effect on your project.
Where Schedule B1 sits in the ASC NEPM
The ASC NEPM is the national framework for assessing site contamination. Schedule B1 sets investigation and screening levels for soil, soil vapour and groundwater. They are used to decide whether further assessment, site-specific risk evaluation or management is warranted. Related Schedules matter in parallel: Schedule B2 for site characterisation and the conceptual site model (CSM), Schedule B4 for site-specific health risk assessment, Schedules B5a to B5c for ecological risk assessment and the derivation of ecological investigation levels, Schedule B6 for risk-based assessment of groundwater contamination, and Schedule B7 for the derivation of the health-based investigation levels.
Investigation and screening levels are not clean-up standards or land-use suitability certificates. An exceedance usually means refine the CSM, check data quality and statistics, then decide whether site-specific assessment or management is needed. State practice adds another layer. In NSW, use the NSW EPA Consultants Reporting on Contaminated Land: Contaminated Land Guidelines and the other statutory guidelines made under the Contaminated Land Management Act 1997. In Queensland, contaminated land investigation documents are prepared under the Environmental Protection Act 1994 framework administered by the Department of the Environment, Tourism, Science and Innovation (DETSI). The relevant guidance includes the Queensland Auditor Handbook for Contaminated Land and DETSI’s approved forms, read alongside the ASC NEPM. In Victoria, EPA publications Assessing and Controlling Contaminated Land Risks (publication 1977) and the Notifiable Contamination Guideline (publication 2008) sit beside the Environment Protection Act 2017 duties. Always check the current jurisdictional instrument before treating a Schedule B1 table as the whole decision.
Schedule B1 soil criteria at a glance
Table 1 Summary of Schedule B1 soil criteria by receptor, land use, soil type and depth of application
| Criteria | Protects | Media and analytes | Land-use settings | Soil type | Depth of application |
|---|---|---|---|---|---|
| HILs (Table 1A(1)) | Human health, all relevant exposure pathways | Soil. Metals and inorganics, PAHs, phenols, pesticides, PCBs and other organics | HIL A, B, C and D | Not adjusted for soil type | Generally the top 3 m for residential use. Site-specific for other land uses |
| HSLs for vapour intrusion (Tables 1A(3) to 1A(5)) | Human health, inhalation of vapour in buildings | Soil, groundwater and soil vapour. TRH F1 and F2, BTEX and naphthalene | HSL A and B (combined), C and D | Sand, silt and clay | Depth to source bands. Soil: 0 to <1 m, 1 m to <2 m, 2 m to <4 m, 4 m+. Groundwater: 2 m to <4 m, 4 m to <8 m, 8 m+. Soil vapour: 0 to <1 m through to 8 m+ |
| EILs (Tables 1B(1) to 1B(5)) | Terrestrial ecosystems | Soil. Arsenic, copper, chromium (III), DDT, lead, naphthalene, nickel and zinc | Areas of ecological significance, urban residential and public open space, commercial and industrial | Site-specific soil properties (pH, CEC, clay content) for some metals | Top 2 m below finished surface or ground level |
| ESLs (Table 1B(6)) | Terrestrial ecosystems | Soil. TRH F1 to F4, BTEX and benzo(a)pyrene | As for EILs | Coarse and fine | Surface to 2 m below finished surface or ground level |
| Management limits (Table 1B(7)) | LNAPL formation, fire and explosion, damage to buried infrastructure | Soil. TRH F1 to F4 | Residential, parkland and public open space, and commercial and industrial | Coarse and fine | No fixed band. Set site-specifically from basement depth, service depth and depth to groundwater |
HILs: Health Investigation Levels for soil
Health Investigation Levels (HILs) are generic soil criteria protective of human health for defined land-use settings. Schedule B1 Table 1A(1) presents HILs for metals and inorganics, polycyclic aromatic hydrocarbons (PAHs), phenols, pesticides, polychlorinated biphenyls (PCBs) and other organics across four land-use settings:
- HIL A Residential with garden or accessible soil (home-grown produce less than 10% of fruit and vegetable intake, no poultry). Also covers childcare centres, preschools and primary schools
- HIL B Residential with minimal opportunities for soil access, such as high-rise buildings and apartments with fully and permanently paved yard space
- HIL C Developed public open space such as parks, playgrounds, playing fields, secondary schools and footpaths. Undeveloped open space such as urban bushland and reserves needs site-specific assessment
- HIL D Commercial and industrial premises such as shops, offices, factories and industrial sites
HILs assume direct and indirect contact with soil for the stated land use. They do not replace vapour intrusion assessment for volatile contaminants, and they do not replace drinking-water or recreational-water criteria where those pathways dominate. For chlorinated solvents, Schedule B1 Table 1A(2) provides separate interim soil vapour HILs for compounds such as trichloroethene and tetrachloroethene. Choose the HIL that matches the current or proposed land use that the decision is about. If a warehouse is being rezoned to townhouses with backyards, HIL D is the wrong yardstick for the future-use decision even if it described the current occupancy.
Soil type and depth. HILs are not adjusted for soil texture. Schedule B1 states they apply generally to the top 3 m of soil for residential use, with site-specific conditions determining the depth for other land uses. That zone reflects gardens, landscaping, footings and routine service excavation. Deeper soils still matter where they will be excavated and brought to the surface, reused as fill, or exposed by cut.
HILs should be applied to soil results with sound statistical interpretation. Many auditors and regulators expect comparison of the 95% upper confidence limit (UCL) on the mean for a defined decision unit, alongside consideration of hotspots and maximum values. In NSW, the NSW EPA Sampling Design Guidelines (2022) set out the expected approach to sampling design and statistics. A single exceedance does not automatically equal an unacceptable risk, and a mean below the HIL does not automatically clear a site if the CSM shows complete pathways and poor spatial coverage.
HSLs: Health Screening Levels for petroleum hydrocarbons
Health Screening Levels (HSLs) address petroleum hydrocarbon contamination. Schedule B1 tabulates HSLs for vapour intrusion for TRH F1 (C6 to C10 less BTEX), TRH F2 (>C10 to C16 less naphthalene), benzene, toluene, ethylbenzene, xylenes (BTEX) and naphthalene in soil (Table 1A(3)), groundwater (Table 1A(4)) and soil vapour (Table 1A(5)). The HSLs were developed by CRC CARE (Friebel and Nadebaum 2011). CRC CARE Technical Report 10 also provides direct contact HSLs and HSLs for intrusive maintenance workers in shallow trenches. Schedule B1 notes direct contact HSLs are unlikely to drive further investigation at most sites, but they should still be checked where impacted soils are accessible or services will be installed through them.
Use HSLs when the CSM includes petroleum sources such as underground petroleum storage systems (UPSS), fuel bowsers, workshops, or hydrocarbon-impacted fill. Do not treat an HSL soil column as a substitute for metals or PAH HILs. Conversely, do not clear a service-station site on HILs alone when BTEX, naphthalene or total recoverable hydrocarbons (TRH) fractions need HSL comparison.
Land use
- HSL A and B Low to high density residential. Schedule B1 presents the two together in the vapour intrusion tables
- HSL C Recreational and public open space
- HSL D Commercial and industrial
Soil type
Vapour intrusion HSLs are tabulated for sand, silt and clay, broadly matched to the soil texture classes in AS 1726. The HSLs assume a uniform soil profile, and Schedule B1 directs practitioners to use the texture making up the greatest proportion of the profile. Where there is reasonable doubt, make a conservative selection (the coarsest applicable grain size, usually sand) or measure the soil properties. Sand values are generally the most conservative because vapour migrates more readily through coarse soil, but silt values are lower for some analytes and depth bands, so check both rows before settling on one.
Depth
HSLs are derived for depth to source. The shallower the source, the lower (more stringent) the HSL, because there is less soil for vapour to attenuate and biodegrade in before it reaches a building. The depth bands are:
- Soil 0 to <1 m, 1 m to <2 m, 2 m to <4 m and 4 m+
- Groundwater 2 m to <4 m, 4 m to <8 m and 8 m+. There are no generic groundwater HSLs for groundwater shallower than 2 m
- Soil vapour 0 to <1 m, 1 m to <2 m, 2 m to <4 m, 4 m to <8 m and 8 m+
Many deeper values are shown as NL (not limiting). NL means the calculated HSL exceeds the soil saturation or groundwater solubility limit, so vapour from that source cannot produce an unacceptable risk at that depth. Table 2 shows how quickly the numbers change with depth.
Table 2 Soil HSLs for vapour intrusion for TRH F1 in sand (mg/kg), ASC NEPM Schedule B1 Table 1A(3)
| Depth to source | HSL A and B (residential) | HSL D (commercial and industrial) |
|---|---|---|
| 0 to <1 m | 45 | 260 |
| 1 m to <2 m | 70 | 370 |
| 2 m to <4 m | 110 | 630 |
| 4 m+ | 200 | NL |
Limits of the generic HSLs
- The HSLs assume slab-on-ground construction. Basements, lift pits and buildings in contact with contaminated groundwater or light non-aqueous phase liquid (LNAPL) need indoor air sampling or site-specific assessment
- Where groundwater impact is less than 2 m deep, use soil vapour measurements to assess vapour intrusion
- Preferential pathways such as service trenches or fractured rock need site-specific assessment
- Hydrocarbon odour inside a building calls for indoor air sampling or immediate action
- Vapour HSLs cover the volatile F1 and F2 fractions only. Heavier F3 and F4 impacts are screened through direct contact HSLs, ESLs and management limits
HSLs are still screening tools. Exceeding an HSL is a trigger for further assessment: better delineation, soil vapour or indoor air measurement, building condition review, or a site-specific vapour intrusion assessment. Being below an HSL does not license ignoring preferential pathways such as service trenches, lift pits, or buildings with damaged slabs.
HSLs on development sites: why the shallow bands are the prudent default
The HSL depth bands describe the relationship between a source and the floor of the building that will be occupied, not the ground surface on the day of sampling. Development changes that relationship. Bulk earthworks can remove metres of soil. Basements, lift pits, detention tanks and service trenches bring occupied space and migration pathways closer to deeper impacts. Impacted soil can be excavated and reused as fill closer to the surface.
A simple example shows the risk. A TRH F1 impact in sand at 2.5 m below existing ground screens against 110 mg/kg for HSL A and B. After a 2 m cut, the same source sits about 0.5 m below the new slab and the relevant value is 45 mg/kg. A result of 80 mg/kg passes the first comparison and fails the second.
Soil type is just as unstable. Natural profiles vary across a site, fill is rarely uniform, and slabs, pavements and services are usually bedded on sand or gravel. A site logged as clay can still end up with a continuous coarse layer between a source and the underside of a building.
Where finished levels, building footprints and basement depths are not fixed, a prudent approach is to:
- Screen soil and soil vapour results against the 0 to <1 m HSL band for the proposed land use
- Adopt the most conservative soil type values (usually sand, but check silt as well) where the profile is variable, uncertain or likely to be altered by fill, bedding or services
- Measure depth to source from the proposed finished surface or floor level, not existing ground, once design levels are known
- Check whether cut or basements will bring groundwater within 2 m of a floor. If they will, generic groundwater HSLs no longer apply and soil vapour data are needed
- Refine to deeper bands or finer soil types only where design drawings and logged soil profiles support it, and record that basis in the report
- Treat any later design change, such as a new basement or lowered finished levels, as a trigger to revisit the HSL selection
Conservative screening is not the same as conservative remediation. An exceedance of a shallow HSL is a prompt to collect soil vapour data or complete a site-specific assessment against the actual design, not a reason to excavate to the lowest number by default. The same logic applies to ecological criteria. Soils below 2 m today can become the root zone after a cut, and EILs and ESLs apply to the top 2 m of the finished surface.
EILs: Ecological Investigation Levels for soil
Ecological Investigation Levels (EILs) protect terrestrial ecosystems from soil contaminants. Schedule B1 provides EILs for arsenic, copper, chromium (III), DDT, lead, naphthalene, nickel and zinc, with the derivation methodology in Schedules B5a to B5c. Many EILs are site-specific rather than a single national number.
- Land use Three settings: areas of ecological significance, urban residential areas and public open space, and commercial and industrial land
- Soil type For copper, zinc, nickel and chromium (III), the EIL is an ambient background concentration (ABC) plus an added contaminant limit (ACL). The ACL depends on cation exchange capacity (CEC) and pH for copper and zinc, CEC for nickel, and clay content for chromium (III). Collect these soil parameters during the investigation, or accept conservative generic values
- Aged versus fresh Schedule B5b treats contamination as aged once it has been in the soil for at least two years. Ageing reduces bioavailability, so ACLs for aged contamination are higher than for fresh contamination. Schedule B1 gives separate fresh and aged values for the metals with soil-specific EILs, and the generic EIL table states the basis for each contaminant. Do not assume every tabulated value is for aged contamination. Recent spills, newly imported fill and soils where contaminants have been freshly mixed or disturbed should be assessed against fresh values unless there is evidence of ageing. State the basis for the aged or fresh assumption in the report
- Depth EILs apply principally to the top 2 m of soil at the finished surface or ground level, which corresponds to the root zone and habitation zone of many species
Apply EILs when ecological receptors matter: landscaped open space that supports soil biota, remnant vegetation, revegetation commitments, or sites where the approval pathway explicitly requires ecological assessment. A common mistake is to run only human-health HILs on a parkland or conservation-adjacent site and declare the soils acceptable. Human health and ecology can diverge. Zinc or copper that is tolerable under a commercial HIL may still warrant ecological attention under an EIL framework.
EILs are investigation levels. Exceedance points to further ecological assessment, refinement of the CSM, or management, not an automatic remediation volume. Background and ambient urban conditions also matter, and the ABC approach in Schedule B1 and Schedule B5b expects practitioners to distinguish site-related contamination from regional soil chemistry before recommending large-scale ecological clean-up.
ESLs: Ecological Screening Levels for petroleum hydrocarbons
Ecological Screening Levels (ESLs) are the ecological counterpart to HSLs for petroleum hydrocarbons in soil. Like EILs, they sit in the ecological risk framework rather than the human-health HIL and HSL tables.
- Analytes TRH F1 to F4, BTEX and benzo(a)pyrene (Table 1B(6))
- Land use The same three settings as EILs
- Soil type Coarse and fine soils, equivalent to coarse-grained and fine-grained soils under AS 1726. Coarse values are equal to or lower than fine values for most analytes, but not all (xylenes, for example), so check both columns where texture is mixed and adopt the lower value
- Depth Surface to 2 m below finished surface or ground level
Benzo(a)pyrene ESLs
The benzo(a)pyrene ESL in Table 1B(6) (0.7 mg/kg for urban residential and public open space) is flagged in Schedule B1 as low reliability. It was based on an older Canadian soil quality guideline that has since been revised, and it is low enough that urban fill with traces of ash or asphalt routinely exceeds it.
CRC CARE Technical Report 39 (2017), Risk-based management and remediation guidance for benzo(a)pyrene, derived higher reliability ecological screening levels that are more than an order of magnitude above the NEPM ESL and broadly consistent with the revised Canadian values. For urban land uses, it also found the revised ecological levels generally sit above the human health criteria, so ecology is unlikely to drive benzo(a)pyrene remediation.
In practice, some auditors have accepted the CRC CARE guidance, or the current Canadian Council of Ministers of the Environment (CCME) soil quality guideline for environmental health (soil contact), as the ecological screening value for benzo(a)pyrene. The CCME values are 20 mg/kg for agricultural and residential/parkland land and 72 mg/kg for commercial and industrial land. Confirm the approach with the auditor or regulator early, report the NEPM ESL exceedance alongside the adopted value, and explain why the alternative is more reliable. Benzo(a)pyrene TEQ must still be compared with the human health HILs.
Use ESLs where petroleum-impacted soils could affect terrestrial ecology, not only where vapour intrusion threatens building occupants. A capped industrial hardstand with no ecological exposure may not need ESL-driven remediation even if ESL exceedances appear in soil tables. An open landscaped verge, future garden beds, or revegetation pads might. Keep the ecological land-use narrative explicit in the report so the ESL comparison is not an orphan table.
Management limits for petroleum hydrocarbons
Management limits are the fifth set of petroleum hydrocarbon numbers in Schedule B1, and the one most easily overlooked. They are not health or ecological risk levels. Schedule B1 adopts them from the Canada-Wide Standard for Petroleum Hydrocarbons in Soil as interim Tier 1 guidance, applied in addition to the HSLs and ESLs, to avoid or minimise:
- Formation of observable LNAPL
- Fire and explosive hazards
- Effects on buried infrastructure, such as hydrocarbons penetrating or damaging in-ground services
Table 3 Management limits for TRH fractions F1 to F4 in soil (mg/kg), ASC NEPM Schedule B1 Table 1B(7)
| Fraction | Residential, parkland and public open space | Commercial and industrial | ||
|---|---|---|---|---|
| Coarse soil | Fine soil | Coarse soil | Fine soil | |
| F1 (C6 to C10) | 700 | 800 | 700 | 800 |
| F2 (>C10 to C16) | 1,000 | 1,000 | 1,000 | 1,000 |
| F3 (>C16 to C34) | 2,500 | 3,500 | 3,500 | 5,000 |
| F4 (>C34 to C40) | 10,000 | 10,000 | 10,000 | 10,000 |
Separate management limits for BTEX and naphthalene are not available, so they are not subtracted from F1 and F2 when comparing results with management limits. This differs from the HSL comparison, where F1 and F2 are reported net of BTEX and naphthalene.
- Land use Two settings: residential, parkland and public open space, and commercial and industrial. Schedule B1 notes they may have less relevance at operating industrial sites, including mine sites, with no or limited sensitive receptors in the area of potential impact
- Soil type Coarse or fine under AS 1726. Coarse values are equal to or lower than fine values for every fraction, so coarse is the conservative choice where texture is mixed
- Depth No fixed depth band. Schedule B1 requires site-specific consideration of basement depth, service depth and depth to groundwater to set the maximum depth to which the limits apply. On development sites where basements and services are not yet designed, apply them through the full depth that could be excavated or intersected by services
Management limits matter most for heavier fuels and oils. There are no vapour HSLs for F3 and F4, so a diesel, lubricating oil or heavy fuel oil impact can pass the vapour HSLs and still exceed a management limit. Exceedance calls for further site-specific assessment and management, such as LNAPL assessment, protection of services, or removal of gross impacts. Meeting management limits does not remove notification or administrative control obligations under state legislation.
Soil, groundwater and vapour: matching media to criteria
Schedule B1 criteria are media-specific. Mixing them is one of the fastest ways to produce a misleading summary table.
- Soil HILs, EILs, ESLs and management limits apply to soil concentrations for the relevant land use, soil type and depth
- HSLs include soil, soil vapour and groundwater tables. Pick the table that matches the sample you actually collected and the pathway you are testing
- Groundwater results are compared with the groundwater investigation levels in Schedule B1 Table 1C and the guidelines relevant to the environmental values, with Schedule B6 for risk-based assessment. For aquatic ecosystems, practitioners now generally use the ANZG (2018) default guideline values, which replace the ANZECC/ARMCANZ (2000) values referenced in Table 1C. Drinking water and recreational water comparisons use current NHMRC guidance. Do not paste soil HILs next to groundwater results
- Soil vapour and indoor air need vapour HSLs, interim soil vapour HILs for chlorinated compounds, or a site-specific vapour assessment. Soil HILs do not demonstrate that vapour intrusion is acceptable
Depth and soil type change vapour HSLs. Shallow sand beneath a residential slab is not the same exposure setting as deep clay under a warehouse. If the report quotes a single HSL without stating land use, soil type and depth assumptions, the comparison is incomplete.
Human health versus ecology: run both when both matter
Human-health criteria (HILs, HSLs) and ecological criteria (EILs, ESLs) protect different receptors. A competent assessment states which receptor sets are relevant in the CSM and reports both where both are complete or plausible. Typical patterns:
- High-density residential with little soil access may be driven by vapour HSLs and limited HIL B soil contact, with low ecological weight
- Low-density residential with gardens usually needs HIL A plus EILs and ESLs for urban residential garden soils
- Public open space often needs HIL C and ecological criteria for turf and landscaping soils
- Commercial or industrial sites may be HIL D and HSL driven for workers and vapour, with ecology only where soft landscaping or off-site migration to sensitive environments is real
- Any petroleum-impacted site needs management limits checked alongside HSLs and ESLs
Do not hide ecological exceedances behind a “human health acceptable” conclusion, and do not imply ecological clearance from a human-health-only table.
Common misuse of Schedule B1 criteria
- Using HIL D on a future residential development because the site is currently industrial
- Clearing petroleum sites on metals HILs without HSL comparison for BTEX, naphthalene and TRH fractions
- Selecting a deeper HSL band from existing ground level on a site that will be cut or will have basements
- Ignoring soil type when selecting vapour HSLs, or adopting clay values where the profile is mixed
- Omitting management limits, so F3 and F4 impacts are only compared with ESLs
- Subtracting BTEX and naphthalene from F1 and F2 before comparing with management limits
- Applying soil HILs to groundwater or soil vapour results
- Treating any exceedance as an automatic excavation volume, or treating any non-exceedance as site closure, without a CSM and statistics
- Applying aged EILs to recent spills or freshly imported fill without justification
- Driving remediation off the low reliability benzo(a)pyrene ESL without considering CRC CARE or CCME values agreed with the auditor
- Skipping EILs and ESLs on open space or revegetation sites, or only testing current surface soils when earthworks will expose deeper soils
- Comparing laboratory totals to criteria without checking units, moisture basis, silica gel clean-up or the correct TRH fraction
- Using Schedule B1 as a waste classification table for off-site disposal. Waste classification follows state waste guidelines, not HILs
- Forgetting contaminants that sit outside the Schedule B1 tables and need current national or state guidance. PFAS, for example, should be assessed under the PFAS National Environmental Management Plan Version 3.1 (PFAS NEMP 3.1)
How practitioners should present Schedule B1 comparisons
A usable results section names the land use scenario, the criteria family, the media, and the decision unit. It states the soil type and depth band adopted for HSLs, EILs, ESLs and management limits, and the design levels those choices rely on. It shows the CSM pathways that justify those choices. It explains statistics (95% UCL, maxima, stratification by fill versus natural) in plain language. Where criteria are exceeded, it states the next technical step: more sampling, vapour testing, site-specific risk assessment under Schedule B4 or Schedules B5a to B5c, remediation options, or management controls. Where criteria are met, it still records residual uncertainties such as data gaps, preferential pathways or contaminants without generic criteria.
Auditors, councils and lenders read for consistency. If the executive summary says “compliant with NEPM” while the tables mix HIL A and HIL D, omit HSLs on a UPSS site, or use a 2 m to <4 m HSL band on a site with a planned basement, expect questions. Keep the narrative, the tables and the recommendations aligned.
Practical takeaways
- HILs screen soil for human health by land use, generally to 3 m for residential use. Match A, B, C or D to the decision land use, not only the current tenancy
- HSLs screen petroleum vapour risk by land use, soil type (sand, silt, clay) and depth to source. Shallow sources and coarse soils give the lowest values
- On development sites, default to the 0 to <1 m HSL band and the most conservative soil type until finished levels and basement depths are fixed
- EILs and ESLs protect terrestrial ecology in the top 2 m of the finished surface. EILs need site soil properties and a fresh or aged basis, and ESLs need coarse or fine selection
- Management limits address LNAPL, fire and explosion, and service damage for TRH F1 to F4, with depth set by basements, services and groundwater
- Keep media separate. Soil, groundwater and vapour each need the matching Schedule B1 table or water quality guideline
- Exceedances trigger assessment and are not automatic clean-up standards. Non-exceedances are not automatic closure without a sound CSM
- Do not use Schedule B1 as a waste classification shortcut, and check parallel guidance for contaminants outside the Schedule B1 tables
Key references
- National Environment Protection Council (2013) National Environment Protection (Assessment of Site Contamination) Measure 1999, as amended, Schedule B1 Guideline on Investigation Levels for Soil and Groundwater
- CRC CARE (2017) Risk-based management and remediation guidance for benzo(a)pyrene, CRC CARE Technical Report 39
- CCME (2010) Canadian Soil Quality Guidelines for the Protection of Environmental and Human Health: Polycyclic Aromatic Hydrocarbons
- Friebel E and Nadebaum P (2011) Health screening levels for petroleum hydrocarbons in soil and groundwater, CRC CARE Technical Report 10
- ANZG (2018) Australian and New Zealand Guidelines for Fresh and Marine Water Quality
- Standards Australia, AS 1726 Geotechnical site investigations
Contaminated land advice | Preliminary site investigations | Detailed site investigations | Remediation | UPSS services | Talk to iEnvi
Need help applying Schedule B1 on your site?
iEnvi provides practical, senior-led environmental consulting across contaminated land, remediation, ecology and environmental risk. We can help with criteria selection for your site and design levels, conceptual site models, soil vapour assessment and peer review of existing reports. Call 0411 492 159 or contact iEnvi to discuss your project.
Need advice on this issue? iEnvi provides practical, senior-led environmental consulting across contaminated land, remediation, ecology and environmental risk.
PSI services DSI services UPSS investigation and validation Ecological risk assessment Talk to iEnvi