NSW Waste Classification for Excavated Soil: The Six Steps, VENM and ENM Explained

How is excavated soil classified for disposal or reuse in NSW?

In New South Wales (NSW), the waste generator must classify excavated soil using the NSW Environment Protection Authority (EPA) Waste Classification Guidelines, Part 1: Classifying waste (2014). The guidelines set six steps that must be followed in order: special waste, liquid waste, pre-classified waste, hazardous characteristics, chemical assessment, then putrescible or non-putrescible. Most soil is classified at Step 5 by comparing laboratory results with the guideline thresholds. Clean soil may instead be virgin excavated natural material (VENM), or it may qualify for reuse as excavated natural material (ENM) under the EPA’s resource recovery order. If no chemical assessment is done at Step 5, the soil must be classified as hazardous waste.

Every truck of soil that leaves a NSW construction site needs a lawful destination, and the receiving landfill or reuse site will want to see a waste classification before it accepts the load. Getting the classification wrong is expensive in both directions. Over-classify and you pay restricted solid waste rates for soil that could have gone to a general solid waste landfill or been reused. Under-classify and the generator carries the legal risk if contaminated soil ends up somewhere it should not.

This article explains how the NSW framework works for excavated soil, where the common traps sit, and how VENM and ENM fit alongside formal waste classification. It is written for developers, builders, project managers and civil contractors, and it is general guidance only. The classification for your material depends on its history, its condition and the test results. Other states use different systems, for example EPA Victoria’s waste categories and Queensland’s regulated waste framework administered by the Department of the Environment, Tourism, Science and Innovation (DETSI), so the NSW rules below should not be applied elsewhere.

Who is responsible for classifying soil?

The NSW EPA is clear that classifying waste is the responsibility of whoever generates it. On a development site that is usually the landowner or the head contractor, not the excavation subcontractor or the landfill. In practice the generator engages an environmental consultant to plan the sampling, interpret the results and prepare a waste classification report, but the obligation stays with the generator.

The six waste classes are defined in Schedule 1 of the Protection of the Environment Operations Act 1997 (POEO Act):

  • special waste
  • liquid waste
  • hazardous waste
  • restricted solid waste
  • general solid waste (putrescible)
  • general solid waste (non-putrescible).

Clean or lightly impacted soil normally ends up as general solid waste (non-putrescible). Soil with higher contaminant levels may be restricted solid waste or hazardous waste, and soil containing asbestos is special waste.

The six steps, applied to soil

Part 1 of the guidelines says the steps must be followed in order, and once a class is established at one step you stop. For excavated soil, the steps play out as follows.

Step 1: Is it special waste?

Special waste includes asbestos waste, clinical and related waste, and waste tyres. For soil, asbestos is the one that matters. Any soil containing asbestos is asbestos waste, and therefore special waste, regardless of how little asbestos is present.

Asbestos is also the main exception to the stop rule. Where special waste is mixed with restricted solid or hazardous waste, the guidelines require it to be classified as both and managed as both. So asbestos-impacted fill that also carries elevated lead or hydrocarbons still needs chemical assessment, and the result can change which landfills will accept it.

Step 2: Is it liquid waste?

Liquid waste is waste with an angle of repose of less than 5 degrees, that becomes free-flowing at or below 60°C or when transported, or that generally cannot be picked up with a spade. Saturated slurries from piling, drilling muds and some dewatering sludges can fall into this class. Separating or dewatering the material may allow the solids to be classified on their own, with the liquid fraction managed separately.

Step 3: Is it pre-classified?

Some wastes are pre-classified by the EPA. For soil, the important one is VENM, which is pre-classified as general solid waste (non-putrescible). VENM is natural material such as clay, gravel, sand, soil or rock fines that has been excavated from areas not contaminated with manufactured chemicals or process residues from industrial, commercial, mining or agricultural activities, and that does not contain sulfidic ores or soils or any other waste.

Building and demolition waste is also pre-classified as general solid waste (non-putrescible), but the definition expressly excludes excavated soil. Fill with brick, concrete or tile fragments through it is not building and demolition waste just because it contains rubble. It still needs to be assessed as soil.

Step 4: Does it have hazardous characteristics?

Waste is hazardous if it is a dangerous good under certain classes of the Australian Code for the Transport of Dangerous Goods by Road & Rail (ADG Code), such as flammable solids, toxic substances or corrosives. This step is rarely triggered by soil, although grossly impacted material, such as soil saturated with fuel near a leaking tank, should be considered here.

Step 5: Chemical assessment

Most excavated soil is classified at this step. The generator must choose the contaminants that are known or likely to be present, based on site history and the processes involved, and must be able to justify that selection and keep records of it. If the generator chooses not to carry out a chemical assessment, the soil must be classified as hazardous waste. The guidelines also state that hazardous waste cannot be disposed of in NSW without treatment first, which is why skipping the testing is rarely a sensible saving.

The chemical assessment uses two measurements:

  • Specific contaminant concentration (SCC), the total concentration in the soil in milligrams per kilogram (mg/kg)
  • Leachable concentration, measured by the toxicity characteristics leaching procedure (TCLP), in milligrams per litre (mg/L).

The SCC test comes first and acts as a screen. If every result is at or below the contaminant threshold for general solid waste (CT1), the soil is general solid waste. If results exceed CT1 but sit at or below CT2, the soil is restricted solid waste, unless TCLP testing shows the contaminants are not leachable enough to warrant that class. Where CT2 is exceeded, the soil is hazardous waste unless TCLP testing is done, and the combined SCC and TCLP thresholds in Table 2 of the guidelines decide between general solid, restricted solid and hazardous waste.

The guidelines recommend calculating the mean, standard deviation and 95% upper confidence limit (UCL) of the mean for each contaminant, and checking that the 95% UCL is at or below the relevant threshold. That only works with enough samples, which is one reason a single grab sample from a stockpile is a weak basis for classification. The NSW EPA Sampling Design Guidelines (2022) set out how to plan sample numbers and interpret the statistics.

Step 6: Putrescible or non-putrescible?

General solid waste is putrescible unless it is shown to be non-putrescible. Natural soil is not capable of significant biological transformation, so it is normally non-putrescible, but the report should say so. Soil mixed with large amounts of vegetation, organic sludges or food waste needs more thought.

Common soil thresholds at a glance

The table below compares a selection of CT1 and CT2 values from Table 1 of the guidelines with the absolute maximum concentrations in the ENM order. For most contaminants it shows why soil that passes comfortably as general solid waste can still fail ENM.

Contaminant General solid waste CT1 (mg/kg) Restricted solid waste CT2 (mg/kg) ENM absolute maximum (mg/kg)
Arsenic 100 400 40
Lead 100 400 100
Nickel 40 160 60
Mercury 4 16 1
Benzo(a)pyrene 0.8 3.2 1
Total polycyclic aromatic hydrocarbons 200 800 40
Benzene 10 40 0.5
Petroleum hydrocarbons C10 to C36 10,000 40,000 500

Sources: NSW EPA (2014a), Table 1; NSW EPA (2014b), Table 4. The ENM order also sets maximum average concentrations, and both documents list other contaminants not shown here. Always check the current published versions.

Two practical points stand out. First, benzo(a)pyrene in fill containing ash, slag or bitumen fragments often pushes soil past CT1 even when everything else is low. Second, the nickel CT1 of 40 mg/kg can be exceeded by natural soils derived from basalt and other mafic rocks. In that case TCLP testing may show the nickel has low leachability, and the soil can then often be classified as general solid waste, but only if the testing is done.

VENM, ENM and waste: three different pathways

People often use these terms loosely on site, but they mean different things in law.

VENM is pre-classified as general solid waste (non-putrescible) and can be received at sites lawfully able to accept it. The burden is on the generator to show the material meets the definition. That usually means a site history review showing no potentially contaminating land uses, field observations, and enough testing to support the claim. A site with former market gardens, orchards, fill, industrial use or service station history is unlikely to produce VENM without careful separation of natural and impacted material.

ENM is regulated under the Excavated Natural Material Order 2014 and the matching exemption, issued under the Protection of the Environment Operations (Waste) Regulation 2014. ENM is naturally occurring rock and soil that contains at least 98% natural material by weight and does not meet the VENM definition. It cannot include material from a hotspot, material that has been processed, or material containing asbestos, acid sulfate soil, potential acid sulfate soil or sulfidic ores. When the order is met, ENM can be supplied for use as engineering fill or in earthworks without being disposed of as waste.

The ENM order is prescriptive. The generator must prepare a written sampling plan, use a laboratory accredited by the National Association of Testing Authorities (NATA), meet both maximum average and absolute maximum criteria, give the receiver a written statement of compliance, and keep records of the sampling and test results. Receivers commonly ask to see the results as well. Minimum sample numbers depend on the volume:

  • for stockpiles, the order sets 3 samples for less than 500 tonnes, rising to 10 samples for 3,000 to 4,000 tonnes, with the sequence repeated for larger stockpiles
  • for in situ material, discrete samples are required (no compositing), with sampling point numbers set by site area and additional samples at depth, as set out in the order.

Anything that is not VENM and does not meet the ENM order is waste, and its classification under the six steps decides where it can go. Some other reuse options exist under different resource recovery orders, or under site-specific exemptions issued by the EPA, but those have their own conditions.

Traps that catch projects out

  • Testing too late. Classifying soil after it has been excavated and stockpiled usually means mixed material, more samples and a site that cannot be worked while results are pending. In situ classification during the design or approvals stage is cheaper and gives earthworks contractors certainty.
  • Picking the wrong analytes. The contaminant list must reflect the site history. A standard suite of metals, total recoverable hydrocarbons (TRH), benzene, toluene, ethylbenzene and xylenes (BTEX) and polycyclic aromatic hydrocarbons (PAHs) may miss pesticides from former agricultural land or per- and poly-fluoroalkyl substances (PFAS) near firefighting training areas.
  • Forgetting PFAS. The EPA issued an addendum to Part 1 in 2016 that adds SCC and TCLP thresholds for perfluorooctane sulfonate (PFOS) plus perfluorohexane sulfonate (PFHxS), and for perfluorooctanoic acid (PFOA). Where PFAS may be present, these compounds must be included in the Step 5 assessment. The PFAS National Environmental Management Plan Version 3.1 (PFAS NEMP 3.1) is the national framework for PFAS investigation, soil reuse and disposal, and should be read alongside the NSW thresholds.
  • Ignoring acid sulfate soils. Part 4 of the guidelines sets out how excavated acid sulfate soils are classified and managed before disposal. They are also excluded from the ENM order. See our article on acid sulfate soils in Australia for more on the investigation and management side.
  • Assuming fill is clean. Imported fill on an older site is one of the most common sources of asbestos, ash and hydrocarbons. Our article When clean fill isn’t clean covers what tends to go wrong.
  • Not tracking asbestos loads. Loads of more than 100 kg of asbestos waste, or more than 10 m² of asbestos sheeting, transported within NSW must be tracked and reported through the EPA’s Integrated Waste Tracking Solution (IWTS), which replaced WasteLocate.

What a good waste classification report includes

A landfill or receiving site operator will look for a report that stands on its own. At a minimum it should include:

  • a clear description and plan showing the material being classified, its location, depth and estimated volume
  • a summary of site history and the reasons for the contaminants chosen for testing
  • field observations, including any asbestos-containing material, staining or odours
  • sampling locations, methods and quality control samples
  • laboratory certificates from a NATA-accredited laboratory, with results compared with the guideline thresholds
  • a statement working through each of the six steps and a final classification
  • any limitations, such as material that was not accessible or that needs reassessment if conditions change.

If unexpected material turns up during excavation, the classification may no longer apply. Our guide to unexpected finds of contamination during construction sets out what to do when that happens.

How iEnvi can help

iEnvi prepares in situ and stockpile waste classifications, ENM and VENM assessments, and soil reuse advice for projects across NSW and other states. We plan the sampling around the site history so the right contaminants are tested the first time, and we work with earthworks contractors so classifications are ready before excavation starts. Find out more on our soil beneficial reuse and waste classification page.

If you need soil classified for disposal or reuse, call us on 0411 492 159 or send an enquiry through our contact page.

References

  • Heads of EPAs Australia and New Zealand. PFAS National Environmental Management Plan, Version 3.1.
  • NSW Environment Protection Authority. (2014a). Waste classification guidelines: Part 1. Classifying waste. https://www.epa.nsw.gov.au/sites/default/files/140796-classify-waste.pdf
  • NSW Environment Protection Authority. (2014b). The excavated natural material order 2014. https://www.epa.nsw.gov.au/sites/default/files/rro14-excavated-natural-material.pdf
  • NSW Environment Protection Authority. (2016). Addendum to the waste classification guidelines (2014): Part 1. Classifying waste. https://www.epa.nsw.gov.au/sites/default/files/addendum-1-to-the-waste-classification-guidelines.pdf
  • NSW Environment Protection Authority. (2022). Contaminated land guidelines: Sampling design, parts 1 and 2.
  • NSW Environment Protection Authority. (n.d.). Tracking asbestos waste using the Integrated Waste Tracking Solution. Retrieved October 7, 2026, from https://www.epa.nsw.gov.au/Your-environment/Waste/transporting-asbestos-waste-tyres/tracking-asbestos-waste-with-iwts
  • Protection of the Environment Operations Act 1997 (NSW).
  • Protection of the Environment Operations (Waste) Regulation 2014 (NSW).

Need advice on this issue? iEnvi provides practical, senior-led environmental consulting across contaminated land, remediation, ecology and environmental risk.

Environmental management plans Contaminated land advice Asbestos in soil advice Environmental management Talk to iEnvi